- Home >
- Engine >
- Cylinder Head Assembly >
- Valve Spring Lock >
- Comp Cams Valve Spring Locks
Valve Spring Locks - Comp Cams
Refine By Vehicle Refine By Brand
Comp Cams Overview:
COMP Cams-Engineered To Finish First COMP Cams manufactures truly superior hydraulic and solid flat tappet, hyd and mechanical roller, and overhead camshafts for everything from OE replacement to full race, designed and manufactured using cutting-edge technology and the finest engineering in the industry. Whether your engine is naturally aspirated, or you run nitrous, or a supercharger or turbo, our cams make more horsepower than any other. Looking for that ultimate hard-hitting muscle car idle? Check out our aggressive new Thump Cams. Match our camshafts up with our competition-grade lifters, valve springs, timing sets, and other supporting components, and you'll experience the ultimate in race-winning reliability!
Engine Subcategories
-
Camshaft and Accessories
-
Complete Engine Solutions
-
Crankshaft and Accessories
-
Cylinder Head Assembly
- Cylinder Head (3,127)
- Cylinder Head Install Kit
- Engine Valve (8,865)
- PCV Valve (296)
- Positive Crankcase Ventilation (196)
- Pushrod (6,506)
- Pushrod End (52)
- Pushrod Guide Plate (59)
- Rocker Arm (3,885)
- Rocker Arm and Pushrod Kit (47)
- Rocker Arm Fulcrum / Pivot Ball (244)
- Rocker Arm Girdle (72)
- Rocker Arm Nut (161)
- Rocker Arm Shaft (425)
- Rocker Arm Shim (11)
- Rocker Arm Stud / Bolt (441)
- Valve Cover (1,832)
- Valve Cover Bolt/Stud (335)
- Valve Cover Hold Down Tab (68)
- Valve Cover Spacer (12)
- Valve Guide (3,475)
- Valve Lash Cap (143)
- Valve Seals (1,245)
- Valve Seat (4,690)
- Valve Shim (854)
- Valve Spring (5,294)
- Valve Spring and Retainer Kit (157)
- Valve Spring Locators (150)
- Valve Spring Lock (843)
- Valve Spring Retainer (1,033)
-
Engine Bearings
-
Engine Block Assembly
-
Engine Dress Up
-
Engine Mounting Hardware
-
Gaskets and Seals
-
Lubrication System
-
Nuts and Bolts / Studs
-
Piston and Accessories
-
Plumbing Hardware
-
Power Upgrade Systems
-
Timing and Accessory Assembly
COMP Cams Street Valve Locks Valve Locks - Stamped - Hardened Steel - 7 Degree - 1-Groove - 3 - 8 in. Valve Stem - Set of 16. Fits many American Motors and Chevrolets ranging from 1965 to 1990.
Brand: Comp Cams
Part #: 603-16
These stock replacement 7 degree valve locks are for stock engine rebuilds and are recommended for street applications with lighter valve spring loads. These locks are stamped and hardened for superior wear resistance.* With valve stem sizes other... more
Starting At
$4.99
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.550 in. Outside Diameter - .710 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 732-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$284.88
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 2 - 4-Groove - 3 - 8 in. Valve Stem - Set of 16. Fits many Chryslers and Dodges ranging from 1959 to 1978.
Brand: Comp Cams
Part #: 627-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failureIncludes:
* 8 pair two-groove
* 8 pair four-grooveThese... more
Starting At
$28.00
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 1-Groove - 11 - 32 in. Valve Stem - Set of 16. Fits many Fords and Buicks ranging from 1963 to 1993.
Brand: Comp Cams
Part #: 614-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failureFits any Comp Cams 10 degree retainer.
Just choose the... more
Starting At
$20.00
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 1-Groove - 3 - 8 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 612-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failureThese race application 10 degree valve locks are designed... more
Starting At
$14.50
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 1-Groove - 11 - 32 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 611-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failureFits any Comp Cams 10 degree retainer.
* 10 degree Super... more
Starting At
$18.88
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 1-Groove - 3 - 8 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 616-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failureThese race application 10 degree valve locks are designed... more
Starting At
$6.60
COMP Cams Street Valve Locks Valve Locks - Stamped - Steel - 7 Degree - 1-Groove - 11 - 32 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 601-16
* With valve stem sizes other than standard appearing on the market it is important to verify that the valve locks match the valve stem. There should always be a small gap between the two halves of the valve stem lock when positioned properly on... more
Starting At
$4.99
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 1-Groove - 11 - 32 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 613-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failureFits any Comp Cams 10 degree retainer.
* 10 degree Super... more
Starting At
$20.88
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.625 in. Outside Diameter - .765 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 733-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$274.95
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 1-Groove - .310 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 618-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failure
Starting At
$21.88
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.625 in. Outside Diameter - .635 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 739-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$259.95
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.550 in. Outside Diameter - .800 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 731-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$282.88
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.625 in. Outside Diameter - .637 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 722-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$304.42
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 4-Groove - 3 - 8 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 626-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failure
Starting At
$35.88
COMP Cams Street Valve Locks Valve Locks - Stamped - Hardened Steel - 7 Degree - 2 - 4-Groove - 3 - 8 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 606-16
* 8 pair 2 groove and 8 pair 4 groove for Chrysler round groove valve configurations
* With valve stem sizes other than standard appearing on the market it is important to verify that the valve locks match the valve stem. There should always be a... more
Starting At
$4.95
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.500 in. Outside Diameter - .700 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 730-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$46.37
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 2-Groove - 3 - 8 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 625-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failure
Starting At
$35.88
COMP Cams Titanium Valve Spring Retainers Valve Spring Retainers - Titanium - 10 Degree - 1.625 in. Outside Diameter - .870 in. Inside Diameter - Set of 16
Brand: Comp Cams
Part #: 735-16
When you upgrade from steel to titanium valve spring retainers you
gain speed and power, because COMP Cams® titanium retainers are
lighter and stronger than steel. Additionally, our Super Lock titanium
design gives you confidence; no longer... more
Starting At
$269.88
COMP Cams Super Valve Locks Valve Locks - Machined - Hardened Steel - 10 Degree - 4-Groove - 11 - 32 in. Valve Stem - Set of 16
Brand: Comp Cams
Part #: 624-16
Wider angle (10°) locks to better distribute the ever increasing valve
spring loads over the retainer than typical 7° locks (see drawing),
reducing the chance of pull-through failure
Starting At
$34.88
